high temperature wearing compound ceramic lining adhesive

BD281 high temperature wearing abrasion resistant repair epoxy compound ceramic lining adhesive

http://www.wearcoating.com/high%20temperature%20resistant%20adhesive/high_temperature_wearing_compound_ceramic_lining_adhesive_4539.html

Performance features of BD281 anti wear high temperature resistant ceramic tile bonding epoxy adhesives:
1. It’s the two components adhesive consist of modified heat resistant toughening resin and special curing agent.
2. Aging resistant,high temperature resistant,corrosion resistant,with good toughness and high bonding strength.
3. Can cure at room temperature,can also heat for curing.
4. With strong initial adhesion,it won’t fall off without using magnet or other support measures during construction,
optimize construction technology and reduce construction costs.
5.The long term temperature resistant can reach to 250 degree,and short term can reach to 280 degree

Product usage of BD281 high temperature abrasion wear resistant ceramic liner repair adhesive:
With very high bonding force to steel,cement,ceramic,aluminum alloy,stainless steel etc.various materials,especially suitable for
the bonding of anti abrasion wearing resistant ceramic tile under the temperature of 280 degree high temperature working condition of
steel mill,power plant etc.

Performance index:

Product name physical state Standard packing Operation time limit
(25℃)
Usable time
(25℃)
Range of application
 BD281 anti abrasion high temperature ceramic bonding adhesive Viscous paste 5kg 0.5h 6h With very high bonding force to steel,cement,ceramic,aluminum alloy,stainless steel etc.various materials,especially suitable for the paste of wear resistant ceramic chip under the temperature of 280 degree working condition on the equipment ceiling and facade.
Item model Color Density
(g/cm3)
shear strength
(kg/cm2)
GB7124-2008
impact strength
(J/cm2)
GB6328-1999
tensile strength
(kg/cm2)
GB6329-2008
Compressive strength
(Mpa)
GB1041-2008
Working temperature
(℃)
BD281 Gray 1.31 113 45 912 97.3 -60-280

How to use:
1.Surface treatment:

Grinding or sand blasting to clean up the dust,greasy dirt and rust on the surface of adherend,finally clean it by cleaning agent.

2.The preparation of high temperature anti wear abrasion cermaic tile bonding repair adhesive
According to the specified requirements,make A and B two component mix uniformly. A:B(the mass ratio)=4:1

3.Using adhesive:
Make the configured adhesive be coating on the adherend surface uniformly.Double spread will get the better bonding effect.

4.Curing:
Initial curing takes about 1~1.5 hours at room temperature,full curing takes about 24 hours at room temperature,heat it up to
the temperature of 80 degree and keep this temperature for 2 hours,then do the post curing,in this way,can get the higher strength(≥18MPa)

 5.Notes:
It’s suitable to configure 300g~500g adhesive every time,too much adhesive is not easy to mix uniformly,every time the usable time of
the configuring adhesive is about 30~40min,the usable time is long for the low temperature,the usable time is short for the high temperature,
can adjust the configuration adhesive quantity according to the actual condition.

Packing specification:
1.Our common packaging:Two-component,packed in a plastic drum, A component: 4Kg/drum, 4 drums/carton;
B component: 1Kg/drum, 12 drums/carton or 8 drums/carton.
2.We could offer professional customized packaging and subpackage services based on our customers’ requirements.

Transportation storage:
Sealed storage in the cool and dry place.The warranty period is 12 months.Avoid placing it upside down,knocking against and
transporting it as a non-dangerous product during transportation.

Special version:
1.This parameter is for laboratory conditions,due to the actual working condition is more complex,suggest the users to do the
pretest according to actual working condition.

2.When the environment temperature is below 15 degree,the curing time will prolong,should take proper heating measure.

3.When the environment temperature is more than 25 degree or the mixing quantity is too large,the curing speed will expedite,
should properly shorten the application time of coating after mixing.

Construction protective measures:
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with
this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash it with clear water.
Should wash it with clear water immediately and see a doctor when splashing into the eyes by careless.

Warm Prompt:
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas
when burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or garbage burning
place treatment.

fire prevention measures:
Should choose dry powder to extinguish fire,can cover and flap it with dry powder,grit(the construction using abrasive) or the
non chemical fiber fabric when the sizing material catching fire.

The packaging actual photo of BD281 high temperature wear abrasion resistant epoxy ceramic adhesives:

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s