road bridge wearing skid resistant compound epoxy coating

BD75 industrial road and bridge anti abrasion wearing skid resistant repair compound epoxy coating

http://www.wearcoating.com/skid%20resistant%20coating/road_bridge_wearing_skid_resistant_compound_epoxy_coating_4563.html

Packaging specification of BD75 industrial road bridge anti wear skid resistant coatings:
Two-component,packed in a plastic drum,10Kg/drum.
We could offer professional customized packaging and sub-package services based on users’ requirements.

Performance features of BD75 anti wearing skid resistant compound industrial road bridge repairing coating:
1.Two components room temperature curing high polymer coating
2.Curing speed is fast,with high bonding strength,the cured product is abrasion wearing resistant,high and low temperature resistant.
3.With good bonding force to for both metal and cement etc.
4.Coating has high cohesion strength,with good aging resistant performance,has flame resistance.

Product usage:
Mainly used in the paving of indoor and outdoor pedestrian footpath anti skid resistant coating.Especially used in the preparation of
anti skid resistant coatings on industrial equipment metal stair passageway.

How to use:
1.Make the adhesive tape be bonding on the periphery of pending-construction part,do the sand blasting,grinding treatment on the
surface of pending-construction part,in order to protecting no needing construction part from pollution.

2.Clean the pending-bonding surface,make sure the pending-bonding surface be clean and dry.

3.According to the weight ratio A:B=10:1,make the B component pour into the A component,it can be put into using after mixing
and stirring uniformly.

4.This adhesive can be brush coating or roller coating,brush coating for 2 times,the time interval for each time brush coating is about
30 min,waiting for 10 min after the second brush coating,sprinkle a thin layer of abrasive material particle,then brush coating a layer of
topcoat,curing for 24 hours at room temperature,we don’t suggest construction when the temperature is below 0 degree,the curing time
will prolong to 48 hours at the temperature of 0-10 degree.

5.The mixing mass ratio of the topcoat: This product(BD75 anti wearing skid resistant compound epoxy coating) : acetic ether=3:1,
mix them uniformly.

6.Remove the adhesive tape and finish the construction.

Performance index:

Project Index Testing standard
Appearance Uniform viscous liquid,without impurities visual inspection
Viscosity(Pa·s,25℃) 4.0±0.6 GB/T2794-1995
Density (20℃  g/cm3 ) 1.21 GB1033-1986
Surface drying time(min) 30~50 GB/7123-1986
weather resistance (UV irradiation for 7 days) Without change GB/T1766-1992
Shore D Hardness 80 GB/10807-1989
Tensile strength (MPa) 49.7 GB/T1040-1992
Shear strength (MPa) 16.6 GB/T2791-1995
Working temperature (℃) -60~200

Notes:
1.Weigh the main agent and curing agent according to the specified mixing ratio,make sure to mix and stir it uniformly.

2.Please use it in time after configuring adhesive,in order to avoid causing the waste after the adhesive thickening.

3.Ethyl acetate is the thinning agent of this product.

4.The coating without curing is afraid of water,try to avoid outside construction in rainy day.

5.The skid resistant coating without curing completely is forbidden to walk.

Storage
This product is the common chemicals,should pay attention to water resistant,fire prevention in the process of transportation and storage,
sealed storage in a cool and dry place,the storage period is 12 months.

Construction protection measure:
1.Wear protective masks,protective glasses and rubber gloves.

2.Washing hands with soap before eating,drinking or smoking.

3.The health hazard after touching with:a few people may have skin allergy phenomenon,seek medical advice in time and avoid contacting
with this product again.Stick to the skin accidentally by rubber material,should use the ethyl acetate to wipe it up,then flush it with clear
water.Splash into the eyes accidentally,should rinse with water immediately and go to a doctor.

4.Residual glue liquid cured product is the non-toxic harmless organic solid,but there may be a poison gas during burning,non-professional
personnel shall not do combustion disposal.

Fire prevention measure:
Ethyl acetate catch fire should choose dry powder fire extinguishing,rubber material catch fire can use dry powder,sand(can also use
construction use abrasive material),or use the non-chemical fiber fabric to cover and swat fast.

Construction case photos show:




Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s